Samsung Stove Burner Stuck on High Repair in Springbank Hill, Calgary
A homeowner in Springbank Hill, SW Calgary, recently contacted Calgary Appliance Fix when they needed a fast Samsung stove burner stuck on high repair in Calgary. The front-left burner on their electric range was locked on full heat, making it impossible to cook safely. Our technician Alex, a licensed appliance technician with over 15 years of experience, was dispatched to diagnose and repair the stove.
The Symptom: Front-Left Burner Stuck on High Heat
The homeowner noticed that the large front-left burner on the stove was always running at full power. Turning the knob down to low or medium made no difference — the burner stayed locked on high heat regardless of the setting. This made the burner impossible to use safely for anything that needed lower or moderate heat, like simmering a sauce or keeping something warm, and created a real risk of scorching food or overheating cookware.
A single burner stuck on high while every other burner cycles normally almost always points to one specific part — the burner control switch (also called an infinite switch) — rather than anything wrong with the burner element itself or the stove's main control board.
The Diagnosis: Failed Burner Control Switch
Alex arrived at the Springbank Hill home and tested the burner control switches behind the front control panel of the range. The front-left burner's switch was confirmed to be the source of the problem — its internal contacts had failed in a way that kept sending full power to the burner element no matter where the knob was set. The wiring and the burner element itself were checked and ruled out, confirming the switch assembly needed to be replaced.
The homeowner was given a clear upfront quote and the repair was approved right away.
Range disassembled by Calgary Appliance Fix technician Alex in Springbank Hill SW Calgary, with the control panel and back access panel removed to reach the burner control switches
The Repair: Burner Control Switch Replacement
Alex removed the range's back access panel to reach the bank of burner control switches, then disconnected the wiring from the failed front-left burner switch. The old switch was compared against the new replacement part to confirm an exact match before installation.
The new burner control switch was wired in, the panels were reassembled, and Alex tested the front-left burner across low, medium, and high settings to confirm it was now heating correctly and responding properly to the knob at every level.
Old failed burner control switch next to new replacement switch, compared side by side by Calgary Appliance Fix technician Alex during the Springbank Hill repair
The stove was fully restored to normal operation in a single visit, and the homeowner was very happy with the fast, same-day turnaround in Springbank Hill, SW Calgary.
Why Burner Control Switches Fail
Every burner on an electric or dual-fuel range with knob controls relies on a burner control switch to cycle power on and off at the right rate for whichever heat level is selected. On low, the switch cycles power briefly and often; on high, it stays closed and sends continuous power to the element. These switches contain internal contacts and a heating coil that wear out over years of daily use, and when the contacts fail in the closed position, the burner gets stuck receiving full, continuous power — exactly like a switch stuck on high.
Because the switch is a small internal component behind the control panel, the problem is often mistaken for a bad burner element or knob. Replacing the actual failed switch, as Alex did in Springbank Hill, resolves the issue completely and restores proper heat control at every setting.
Serving Springbank Hill and All of Calgary
Calgary Appliance Fix regularly serves homeowners throughout SW Calgary, including Springbank Hill, Discovery Ridge, Signal Hill, Aspen Woods, Evergreen, Shawnessy, Woodbine, Lakeview, and surrounding neighbourhoods. We also cover all other quadrants of Calgary and surrounding communities:
NW Calgary — Tuscany, Scenic Acres, Citadel, Hamptons, Silver Springs and surrounding neighbourhoods
NE Calgary — Skyview Ranch, Cornerstone, Saddle Ridge, Coventry Hills and surrounding neighbourhoods
SE Calgary — Auburn Bay, Mahogany, McKenzie Towne, Seton, Midpark and surrounding neighbourhoods
Okotoks — All neighbourhoods throughout town
Chestermere — Full coverage east of Calgary
Langdon — Rocky View County east of Calgary
De Winton — Rural community south of Calgary along Highway 2A
Harmony — Master-planned community near Springbank
Priddis — Foothills community west of Calgary
Bragg Creek — Hamlet west of Calgary near Kananaskis Country
Millarville — Foothills County community southwest of Calgary
Same-day and next-day stove and range repair is available across all of these areas.
📞 Call 403-399-5949 | 🌐 www.calgaryappliancefix.ca | Open 24/7 for bookings
[Video: before-and-after clip of the burner running stuck on high and then cycling correctly after the repair goes here at the end of the post.]
Frequently Asked Questions: Stove and Range Repair in Calgary
Why is my stove burner stuck on high heat?
The most common cause is a failed burner control switch (infinite switch) behind the control panel. When the internal contacts fail in the closed position, the burner receives continuous full power no matter where the knob is turned.
How do I know if my burner control switch needs to be replaced?
Signs include a burner that only runs on high regardless of the knob setting, a burner that won't turn down or cycle properly on low and medium, or a knob that has no effect on heat output at all.
Do you use OEM parts for burner control switch replacements?
Yes. Calgary Appliance Fix uses OEM factory certified parts wherever possible to ensure correct fit and reliable long-term performance.
How quickly can you come for stove repair in SW Calgary?
We offer same-day and next-day stove and range repair throughout SW Calgary including Springbank Hill, Discovery Ridge, Signal Hill, Aspen Woods, and surrounding neighbourhoods. Call 403-399-5949 early in the day for the fastest available slot.
Is it worth replacing a burner control switch instead of buying a new stove?
Yes. A burner control switch replacement is significantly less expensive than a new range and fully resolves heat control issues caused by a failed switch.
Do you offer a warranty on appliance repairs?
Yes. Every repair completed by Calgary Appliance Fix comes with a 90-day warranty. If the same issue returns within that period, we come back at no extra charge.
